The SkyLife

Search This Blog

Subscribe to this blog

Receive NEW Posts to Your email:

Video: JDM Legends

on April 07, 2011

Get link
Facebook
Twitter
Pinterest
Google+
Email

This popped up on the forum today and thought it was worthy of posting, enjoy!

JDM Legends Video

Get link
Facebook
Twitter
Pinterest
Google+
Email

Google+ Badge

Importing a Skyline from Japan you never know what you'll get; My First GTR

EDIT: This thread was updated with more details.

I purchased this red 1992 Skyline GTR, in April 2008. At this time in my life, this was maybe the 4th Skyline I'd ever seen in the flesh. I took it for one test drive, and handed over my cash, I had to have it...

Driving this car was like nothing I'd ever experienced, not to mention the novelty of driving on the right hand side of the car for the first time in my life. Here's a video clip that gives a walk through of the car and its modifications, I made this clip to help sell the car later on - and it did sell, later that summer.

Subscribe to YouTube channel below for more great videos The Experience of owning a GTR
This was a built race car straight from Japan, and I had no clue what I was getting myself into... The car had so many dials, buttons, and switches I was just overwhelmed!

After a few years now, of being involved in Skylines I can say this car had what was typical of most imports - the spaghetti wiring and more quick…

RB26DETT Engine Assembly and Rebuild How to Guide for the RB26 Twin Turbo Motor

Engine Assembly
First things first; we’ll start with the HKS oil pump. (The author uses an upgraded oil pump, take a look at this very detailed technical article about: Why the Nissan Oil Pump Fails) Here are two shots of the housing and rotor cover, all cleaned up and ready to install. In addition to having much larger gears than the stock pump, the HKS pump also has ducts to bring oil to the rear of the rotors, as well. This greatly improves oil flow into the pump, reducing cavitation.

Author Note:Matt of MJR Performance sent us an emailwith details on this write up. This is not the only way to assemble the RB26 motor, there are many different thoughts and ideas, but this is just one way of doing it, as always, follow this guide at your own risk.

You can see the inlet duct for the rear of the rotors on the left. I guess it could be called a “bridge port”. There’s some scuffing from the rotors, but nothing you can feel with a fingernail. Even then, this pump has so much volume over a s…

Nissan Skyline GTR Oil Pump Failure Problems

Oil Pump Problems
These Japanese super cars had a common problem that would often lead to the self-destruction of the motor. The Achilles Heel of the Skyline RB26 motor is the oil pump, I personally caught this issue on my own Second GTR (Build Story) leading me to replace it with a new one . This wasn't a problem on all Skylines, only the GTR's made between 1989 and 1991, after 1991 Nissan fixed the issue. Most people will tell you the problem is the width of the drive on the oil pump gears, they say the engagement area is too small, while that may be true (by appearance), it also isn't the 100% exactly correct answer... The real problem is on the nose of the crank, the clearance between the nose of the crank and the part that drives the oil pump inner gear was too loose. The inner circumference of the oil pump inner drive gear was actually too much larger than the outer total circumference of the crank nose. The extra play had no effect on the motor at low RPM, but at high…

Removing HICAS Delete 4 Wheel Steering How to Guide

The HICAS system is Nissans' attempt at a super-handling 4 wheel steering type of thing, for anyone who's driven a car with 4 wheel steering in any sort of spirited driving, you realize pretty quickly that its less of an aid and more of a downfall.

You see, driving faster than 80 km/hr the system will become active, and as you turn around a corner or make quick steering changes, the rear wheels will turn one degree in and out, for a total three degree sweep while you're driving. This system works really well if you want to change lanes really fast, but if you're more into putting the car sideways in a four wheeled power slide, then the HICAS will become your worst enemy.
As the rear end steps out, the HICAS activates to counter the rear end slide, but because you expected the rear end to come out you've already begun to counter steer. So as you turn the wheel, the HICAS turns the rear wheels, and undoes what you've just done! Suddenly you're swerving wildly a…

AWD service Bleeding ATTESA pump system

When I needed to bleed the ATESSA All Wheel Drive system during an overhaul on the Never Ending R32 GTR Epic Build Story, I found a particularly good walk-through on the forums, and from Tyndago's site. So this is a combination from both. (RBS14 on GTRc and Tyndago). You need Nissan ATF fluid for this application, or any equivalent.
Step 1: Fill the tank 30 mm above MAX line. The tank is located in right rear of your trunk.
Step 2: Open the air bleeder on the oil pump. Crack it open until there is no more air coming out and you get fluid dripping. This air bleeder is located on the pump on top of the rear diff. Bleeder is on right side. Can’t miss it.

Step 3: After you tighten up that bleeder go and turn the ignition on. Don’t start the car just turn the key to IGN (Ignition).
Step 4: You need to unclip the air bleeder connector. This is a white clip located under the dash on the right side behind your kick panel" Opposite side of your ECU" Might be a good idea to un screw …

RB26 Engine Turbo swap Upgrade and Engine Overhaul Guide

RB26 Engine Turbo Swap & External OverhaulThis guide picks up where the Pulling the RB26 Engine walk-through left off. Having just separated the transmission from the engine, we now look to remove the old turbos and then set up the new ones. There is a lot of patience needed to do this, as there are a many fragile parts. It does take quite some time to complete this, maybe even a day or two if its your first time. First thing to do is remove any intake piping that may still be attached, put it off to the side. There is an array of metal and vacuum hoses just above the heat shields, and it wraps around the back-side of the engine, remember to label each line that you disconnect.There is also the water feed line, which spans the length of both heat shields, these lines have been heat cycled for 20 years - and unless you plan to replace with stainless steel braided lines (as I have done) - then you need to be very careful when removing the lines or they will crack, as in the picture b…

Nissan RB26 Engine Removal Guide - Pulling the Motor out of a GTR

This Guide will walk you through the key steps for pulling an engine from a car, whether you're doing a rebuild or motor swap, you'll see step-by-step how I removed this RB26 Engine and got it back together perfectly. The same method I followed here will make working on ANY car fool-proof!

Start by getting a note book, a sharpie marker, Ziploc plastic baggies and masking tape. There are so many connectors, nuts and bolts to keep track of when pulling the engine from the GTR, and believing you can remember where everything goes by heart is a foolish assumption for a first timer. I am assuming this tear down is down from a first timers perspective, so everything will be as detailed as possible. This is by no means the quickest way to remove the engine, nor is it 100% easier then any other way, but this is how I managed to get it done, It didn't cost me an arm and a leg, and everything worked perfectly once all was said and done.
The # 1 rule is: "If you remove it, or unpl…

Nissan Skyline R34 MFD Display Swap into R33 R32

This guide was created by Daniel Hipgrave and published here with his express permission with content from original post/discussion gtr.co.uk/forum - r34 mfd into r33.
For years i've loved the look of the LCD screen in the R34, and a couple of months back I saw a picture on the net of a purple R33 in Hong Kong where someone had retro-fitted the MFD. Since then, I knew I had to do the conversion myself..

Finding an MFD in itself is a hard job. These things cost over a grand from Nissan, and even second-hand command a price of around £700 when working which would be way more than I could spend on one.
A few weeks back, there were a pair of non-working MFDs for sale on here, and even though it was a gamble, the price was so low I couldnt let it get away, so I was the owner of a non-working MFD for £125!

When I got the MFD it was worse than I had imagined (in my head I saw myself swapping a blown fuse, and the unit springing into life!). The fuse had indeed blown, but before it had done, …

Nissan Skyline GTR Build

Picking the right one... October 8, 2008
After the experience I'd had with my first Skyline, I was on the hunt for one that would more suit my level of experience. In the very back of a warehouse, covered in dust, I'd found A 1991 Nissan Skyline GTR in Pearl Metallic red, with roughly 110,000 km on the clock, the reason I chose this one in particular was because it was 100% stock. It had ZERO modifications, not a single thing! and that's such a rare thing to find in these cars, its one of the only ways you can be sure the car is in good condition. We had it up on the lift where we did the inspection, no leaks, nothing out of place, not even any dents or scratches on the frame rails where you usually see evidence of improper jack lifting.
Then we had at it with a compression test... Everything showed above 150 PSI. Stock motors fresh from the factory will see 160 PSI... so showing above 150 on all cylinders was really good, I had found the gem! the oh so rare, un-abused Skyli…

Followers

Home

About

Builds & How to Guides

Cars for Sale

Garage & Shop Reviews

SUBMIT a Review

Downloads

Advertising on The SkyLife

Contact us

The SkyLife Archives

SkyLife External Links Page

Powered by Blogger